Click on a thumbnail to see the full-size image
Multiple Cylinder Misfire or Rough Idle on 2004-'06 Chrysler 3.5L Engines
This information for installers applies to Chrysler models built after Feb. 1, 2004 (MDH 0201XX) equipped with a 3.5L engine (Sales Code EGN).
This bulletin involves rotating all engine exhaust valves, replacing
the valve spring retainer locks with a new design to increase valve
rotation at lower rpm, inspecting/replacing the MAP sensor (as
necessary), and decarbonizing the combustion chamber.
The customer may experience occasional engine misfire (rough-running engine) during certain vehicle operating conditions.
In addition, MIL illumination may also have occurred due to DTC
P0300 - Multiple Cylinder Misfire. Various single cylinder misfire DTCs
may also be present. If the frequency of misfire is high, the
powertrain control module (PCM) may place the engine in “limp-in” mode.
The misfire condition may be caused by one or more engine exhaust
valves that are slow to close due to a buildup of carbon on the valve
1. This condition may occur when the engine is not allowed to run at
engine rpms that are greater than 3,500. At 5,000 rpm or higher, the
engine exhaust valves will rotate if not impeded by high carbon
deposits. Low engine rpms and high carbon deposits are associated with
short-trip driving where the engine is not allowed to fully warm to
normal engine operating temperatures.
Cold ambient temperatures will increase engine warm-up time and
increase the likelihood of carbon deposit buildup on the stem of the
engine exhaust valve. Fuel detergent quality may also contribute to the
condition; the customer may want to try a different brand of fuel.
2. Verify that the engine misfire condition is not caused by faulty engine mechanical or electrical components.
3. If the engine mechanical and electrical systems are operating properly, perform the Repair Procedure.
1. Relieve the fuel pressure.
2. Remove the upper intake manifold.
3. Remove the cylinder head cover(s).
4. Remove the rocker arm and shaft assembly.
5. Clean and mark the tip of each exhaust valve stem at the 12 o’clock
position with a paint marker. The paint mark will be used later to
assist with determining the amount of valve rotation.
6. Remove the spark plugs.
7. Rotate the crankshaft clockwise, until the number 1 piston is at Top Dead Center (TDC) on the compression stroke.
8. Install the compression tester spark plug adapter in cylinder #1
spark plug hole. With the air hose attached to the spark plug adapter,
apply 90 to 100 psi air pressure. This is to hold
the valves into place while servicing the components.
9. Using a valve spring compressor tool (MD 998772A) with the valve
spring adapter (6527 or equivalent), slightly compress the exhaust
valve spring to release tension against the valve and valve spring
retainer (see Figure 1).
10. Remove the valve spring retainer locks and discard the locks.
Note: It is important that the valve rotation section of this repair procedure be performed.
Caution: Only grab the valve stem tip, being careful not to cause damage.
11. Using needle-nose pliers, grab the tip of the valve stem and rotate
the exhaust valve 90° (move the mark to the 3 o’clock position).
12. Install two new valve spring retainer locks (P/N 53022277AA).
13. After installing the locks, release the tension on the valve spring and verify proper installation.
14. Remove Special Tool MD 998772A (1) and the spark plug adapter tool.
15. Repeat steps 7-14 on the remaining five cylinders using the firing
sequence 1-2-3-4-5-6. Make sure the piston is at TDC in each cylinder
of the exhaust valve spring retainer lock that is being removed. When
all the exhaust valves have been rotated 90° and all the exhaust valve
spring retainer locks have been replaced, proceed to the next step.
16. Install the rocker arm and shaft assembly.
17. Install the cylinder head cover(s).
18. Install the upper intake manifold
MAP Sensor Inspection:
1. Inspect the MAP sensor Figure 2 for LX models or Figure 3 for CS models.
a. If the MAP sensor is the new style, no further action is necessary
for the MAP sensor. Proceed to Decarboning Combustion Chamber and
b. If the MAP sensor is the old style, proceed to the next step.
2. Replace the MAP sensor with P/N 05033310AC for LX models or P/N
04896003AB for CS models. If the vehicle is a CS model, be sure the new
sensor opening is facing a downward direction when installed and only
use one fastener.
When complete, proceed to Decarboning Combustion Chamber and Valves.
Decarboning Combustion Chamber and Valves:
Caution: Do not use the Premium Air Intake Cleaner provided with kit 05174566AA for this service action.
Note: Use both fuel tank additives.
1. Pour the Premium Fuel System Cleaner from kit P/N 05174566AA and Combustion Clean P/N 05183546AA, into a full fuel tank.
2. Start the vehicle’s engine and allow it to reach normal operating temperature.
3. Disable the fuel pump by removing the fuel pump relay.
4. Disconnect the fuel supply line quick disconnect fitting from the fuel rail.
5. Install the appropriate adapter, either #31814 or #31815. Be sure to
engage the adapter completely (push until a “click” is noticed).
6. Pour the Premium Combustion Chamber Cleaner from kit P/N 05174566AA, into the cleaning canister.
7. Suspend the fuel injector cleaning apparatus under the hood. The
regulator knob must be fully counterclockwise to the off position.
Connect the cleaning apparatus service hose to the supply adapter.
8. Turn the regulator knob clockwise to the recommended cleaning
pressure (58 psi). Be sure there are no leaks before starting the
9. Start the engine and run at normal idle (or fast idle, 1,200-1,500
rpm, to shorten service time) until the product has been used up and
the engine stalls.
10. When the engine stalls, turn the ignition off.
11. Disconnect the cleaning apparatus and adapter.
12. Reconnect fuel line and the fuel pump relay.
13. Turn the ignition key to the on position to energize the fuel pump.
Check for leaks. Start the engine and run for at least 2 minutes to
clear the fuel system of any residual product.
14. Using the DRBIII or the Star-SCAN, erase any engine DTCs.
1. In a safe vehicle operating location that will allow the vehicle to
be driven safely and at the posted speed limit, accelerate the vehicle
until the engine reaches 4,500 rpm.
2. Hold the engine speed at this rpm for 15 seconds.
3. Slow down and, in a safe location, pull to the side of the road. Allow the engine to idle for five seconds.
4. Repeat steps 1 through 3 five more times.
Courtesy of ALLDATA.