Click on a thumbnail to see the full-size image
In order for the diesel engine to fire in a cold ...
The fuel systems in today’s diesel engines have c...
Diesel Engine Glow Plugs: Not Just For Starting Anymore
Since diesel engines ignite by using the heat of combustion, they usually need help when the climate changes to the cold of winter.
By Bob McDonald
Veteran owners of “old school” diesel engines understand what I’m talking about when I mention the “one-minute of silence.”
This was the time every morning when you would turn the ignition switch to the “on” position and wait for the glow plugs to come on and warm for several seconds before the engine could be started.
In order for the diesel engine to fire in a cold weather, the glow plugs have to come on for a period of time in order to heat the air in the combustion chamber. Anyone who owns a diesel engine will tell you that when the cold weather sets in, your glow plugs had better function.
With modern diesel technology, though, we often forget how spoiled we are today compared to the way things used to be. Now you can go out to your vehicle and cycle the ignition switch to the “on” position and in a period of three to five seconds, you can start your engine. The glow plug used now can reach 1,000 degrees F in three seconds. Consider the dramatic changes that have taken place!
First of all, in today’s diesel engines, the fuel system has changed. Now diesel engines are equipped with high-pressure fuel injection systems that inject diesel into the combustion chamber with a precisely metered amount of fuel at a precise time. Injection pressures can reach as high as 30,000 psi on common rail systems. Having higher pressures and metered fuel at the right time means more efficiency, less pollution and lower fuel consumption.
In order to utilize these higher injection pressures, the combustion chamber and piston designs had to be changed. Pistons were redesigned to create more efficient combustion of the diesel fuel along with the combustion chamber creating more swirl. These two elements created a much quieter diesel that was more powerful and more fuel efficient, and it didn’t require as much glow plug “on-time” for starting.
I know you’re probably wondering what the big deal is with regard to glow plugs. The biggest reason diesel technology changed was the fact that tighter emissions for diesel engines were coming into effect. The government wanted to reduce the amount of diesel hydrocarbons and nitrogen oxide levels being emitted from diesel engines. Now, this is where the importance of the glow plugs comes in. Not only do the glow plugs cycle to aid the engine during cold weather start up, but also after the engine is cranked they will continue to cycle to reduce the amount of start-up emissions. This helps reduce the smoke that most diesel engines produce when being cranked on cold mornings.
Even though the engine is running and the glow plug indicator is not illuminated in the dash, the glow plugs will cycle anywhere from 3 to 5 minutes after start up. This helps reduce the amount of start-up emissions by 60 percent and also helps reduce build up of soot that would typically be trapped in the regeneration filter (DPF).
But now, engine manufacturers are advancing glow plug technology to take diesel engine development even further. The glow plug now contains a pressure transducer called a “Glow Combustion Sensor” or GCS.
Not only can the GCS heat the combustion chamber, but it can also measure pressure inside the combustion chamber. Modern electronic diesel engines have always been considered “open-loop” design. This means that the electronics of the vehicle have set parameters under which the engine will run based on inputs received. They inject a metered amount of fuel based on throttle position, MAP, barometric pressure, coolant temp and oil temperature.
But these engines have no oxygen sensor in the exhaust system and therefore can not control situations where the engine may be too rich or too lean. The engine computer only knows that the metered amount should be close to what is needed. The engine does not have any feedback as to whether it was too much fuel or not enough.
By using the GCS, this creates a form of a “closed-loop” design. Now the engine computer can see what is happening inside the combustion chamber by measuring the pressure of combustion and make changes based on inputs received. This would be the equivalent of eight oxygen sensors in the engine monitoring and controlling fuel. Information like this a “real-time” measurement of pressure in individual cylinders allows for corrections to fuel during the warm-up period, under boost, during the EGR cycle and while cruising.
This all comes down to the fact that diesel engines are becoming more popular than gasoline. Yes, I said it. Diesel engines are no longer the “clanking” and “knocking” bucket of bolts they use to be. Frankly, when GM introduced its version of the diesel engine in passenger cars back in the ’70s, I think it ruined a whole generation of buyers for diesel engines.
However, the generation is changing. Diesel engines are more efficient and make more power at a lower rpm. Automakers are looking into more diesel-operated vehicles in order to achieve lower fuel economy along with fewer emissions.
The question that I often get is, why do other countries have so many diesel powered vehicles? The only answer that I have found universally is the fact that many of those countries have lower emissions standards than ours.
But it looks as though things are changing. Emissions standards are rising around the world and acceptance of diesel technology is increasing here in the U.S. True, diesel engines do cost more and are more expensive to repair.
At the end of the day, you have to ask yourself this question: “Do you want to give your money to the international companies who are helping us to develop the technology for these engines or do you want to give your money to the oil-producing countries?”
You are going to spend money regardless, it’s just a matter of WHO you are going to give your money to!