A New 'Finish' in Honing - Engine Builder Magazine

A New ‘Finish’ in Honing

For years, engine builders have been honing cylinders with a coarse stone followed by a finishing stone. Then ring materials changed, requiring an additional very fine finishing stone to follow. Now current technology demands an added step to create an even cleaner, burr-free finish.

However, even with these conventional honing techniques, peaks of folded and torn metal still remain in bores. No amount of washing with an ordinary brush could remove this material. A too-rough bore results in scuffing and rapid wear of components, poor ring sealing, reduced component life and oil consumption. This is especially a problem with today’s thinner, low-tension piston rings. Piston ring manufacturers now lap the rings to replicate seating. With the use of ultra-finish hones, cylinder wall technology has also been elevated to pre-seated quality.

Confusion about this hone tool arises from the many different names given to the same tool and process; Plateau hones, soft hones, whisker hones and ultra-finish hones all do the same thing. Without enlarging the bore, they sweep across the surface to remove jagged peaks, folded and torn material.

The ultra-finish hone consists of a mono-filament strand that is extrude-molded with a fine abrasive material. This abrasive filament can be mounted to different types of holders, but usage and performance is identical. This product is available in holders and brush-type tools, for use with many of the current hones – portable or automatic. Tooling suppliers also offer a selection of small diameter ultra-finish hones that can be used with a simple, pistol-grip drill.

During use, the ultra-finish hone will travel at a light load pressure, closely simulating rpm at which the cylinder was initially honed. Rotation can be reversed when using a portable hone. Its purpose is to slightly deburr the edges of and to remove folded and partially severed material from the cylinder face, the area piston rings actually ride on. The ultra-finish hone is not designed to clean out grooves established by coarse honing or to deglaze cylinders. By design, the ultra-finish hone is used to prepare the cylinder bore for immediate ring seal with little, if any, material loss from cylinder wall on initial engine start-up. This minimizes ring abrasion and broken cylinder wall material migrating to our oiling system. Now we have a near perfect situation, a lapped ring passing over a fully prepared cylinder.

CAUTION: Don’t over do the cylinder with a ultra-finish hone. Sixteen to eighteen strokes are the maximum. Strokes beyond this can produce a finish too smooth to retain adequate lubrication for wear resistance and infinite cylinder pressure sealing.

For engine builders who are not yet equipped with a profilometer, here is a slick little test that illustrates the effect of ultra-finish honing. After finishing a cylinder with conventional finishing techniques, dry the cylinder surface area. Take a cotton ball and lightly contact the cylinder rotating around 2 or 3 surface inches. Cotton strands can be seen hanging, snagged on the wall. Now use the ultra-finish hone on the cylinder with liberal amounts of honing oil. Repeat the cotton ball test after using the ultra-finish hone and see the difference. A very noticeable difference should occur with the number of cotton strands, almost no retention! Not a very scientific test, but a good indication of what type of finish has been established in that cylinder. This same finish can be achieved in many other applications, valve guides, lifter bores and piston pin bushings.

Adding this step in your honing procedure will finalize the plateau finish. Rings will seal without abrasion, compression is maximized, and better oil control will lower emissions. Ends scuffing and scratching, prevents premature wear of valve guides, stems, lifters, etc. You now have the tools and knowledge, add the ultra-finish hones to your honing process to completely finish the job.

Source: Goodson Tools

You May Also Like

Shop Solutions July 2023

Engine and machine shop tips and tricks.


To precisely shorten bolts in the lathe, I made slotted collets for each bolt diameter. They are fractional in length to measure off the end, so you know where to cut for your length. I’ve used large O.D. valve guides and aluminum round stock. Just make the collet big enough to clear the bolt flange, hex or socket head.

Shop Solutions June 2023

Engine and machine shop tips and tricks.

Pennzoil and API on Developing Motor Oil Standards

For more than 90 years, Pennzoil has worked alongside the American Petroleum Institute (API) to ensure Pennzoil products meet – and often exceed – the stringent requirements of motor oil specifications implemented to best help protect the performance of your engine. Related Articles – Nitrous Update – Heavy-Duty Diesel Engines, Equipment and Replacement Parts – Diesel Piston

Nitrous Update

The use of nitrous oxide in diesel engines is not a new concept. In fact, it has been used in drag racing for decades. However, it is only in recent years that it has gained widespread popularity in the worlds of diesel truck pulling and drag racing. Now, it seems as if almost everyone in the competitive scene is using it. 

Heavy-Duty Diesel Engines, Equipment and Replacement Parts

Relying on OE manufacturers like Caterpillar, Cummins, Detroit Diesel and Waukesha has always been an option, but diesel equipment owners are now more than ever seeking the aftermarket as a more viable solution for replacement parts.

Other Posts

Diesel Transmissions

It’s no longer a secret… heck, it’s no longer that special for a diesel engine to make 1,000-plus horsepower. It’s become commonplace, and due to that increased capability, it seems these days, OE manufacturers are rating transmissions at their absolute limits.

The Engine Cummins Never Built: A Look at the 6.4L Cummins

With increased technology in turbo systems as well as fuel systems, the final limits of the 6.4L Cummins have not yet been discovered. These engines are capable of being a competitor in any event, whether it be truck pulling, drag racing, or cruising the strip.

Stock and Performance Diesel Work

Drew Pumphrey, owner of D&J Precision Performance, weighs in on stock vs. performance work in the shop and finding a balance between the two.

May Shop Solutions 2023

Engine and machine shop tips and tricks.