Audi Pioneers Electric Turbo Technology - Engine Builder Magazine

Audi Pioneers Electric Turbo Technology

audi-tdiNow there is a solution to dreaded lag which accompanies turbochargers at low rpm, and it’s one you’d be surprised hasn’t been tried earlier.

The primary hurdle when it comes to turbocharging over supercharging has been the lag encountered at lower engine outputs. One solution to this has been to use a twin turbo setup, with a smaller  compressor to be run at lower rpm and a larger one to augment when output is higher. Even this isn’t a perfect model, however, and while more and more manufacturers across the industry are adopting turbos, a number have abstained, citing performance concerns, notably Jaguar.

Audi seeks to rectify this with an electric turbocharger setup. This design will use an electric motor to drive the turbo at lower rpm, until engine output is sufficient to drive the turbo by exhaust gases. Now, instead of waiting for the exhaust gases to reach a suitable level, power is available almost instantaneously. In Audi’s design, the electrified turbo, which would be the smaller of the two in a twin turbo layout, would draw power from energy gained by regenerative braking(KERS) systems, so that no engine power is used to spin it. We don’t have any information about what kind of a battery pack will be employed to store this energy, however. The concept could also be used in conjunction with hybrid car technology, as energy could be diverted from the primary battery packs to spin the electric compressor.

The incredible potential of this technology is obvious. Reducing the lag inherent to turbocharging would aid in acceleration, as well as cornering, when rpm levels drop significantly due to braking. Audi reports significant improvements in both of these categories. Audi’s design may even overpower superchargers at lower outputs, as since electricity is already on hand, delivery could be near instantaneous. The technology still has yet to be explored in depth, and it hasn’t been applied to any production vehicle yet; it has been used in certain racing series for quite some time, however. Audi says that the technology will appear on its RS-5 concept(pictured above,) which employs Audi’s 3.0 liter TDI engine.

Courtesy of Speedville.com.

You May Also Like

Shop Solutions March 2024

I always keep a pair of needle nose pliers and a small, straight screwdriver in my blast cabinet to hold small parts when blasting.

Engine Builder and Engine Pro present Shop Solutions in each issue of Engine Builder Magazine and at enginebuildermag.com to provide machine shop owners and engine technicians the opportunity to share their knowledge to benefit the entire industry and their own shops. Those who submit Shop Solutions that are published are awarded a prepaid $100 Visa gift card. Submit your Shop Solution at [email protected]. You must include your name, shop name, shop address and shop telephone number. Submitted Shop Solutions not published will be kept on file and reevaluated for each month’s new entries.

Degreeing the Camshaft and Checking Valve-to-Piston Clearance

Jeff McCord of LinCo Diesel Performance walks you through degreeing a camshaft and checking valve-to-piston clearance.

Designing a Better LS Engine

After a customer wanted a Steve Morris Engines’ SMX in an LS version, Steve saw the upside and potential in the market, and a challenge to build a better LS.

The Importance of a Good Valve Job

The valve job ensures the mating surfaces of the valves and the seats properly control the air/fuel mixture.

Other Posts

Thermo-Tec Rogue Series Turbo Covers

The dual-layer construction increases performance and durability while controlling temperatures.

turbo cover
The Winners of 25th Annual TX2K

After a week of racing, the 25th TX2K is in the books, and champions have been crowned in the 13 drag racing classes, as well as four roll racing classes. The event, which started in 2000, has become an annual proving ground to see where the mark stands in a multitude of classes, as well

CP-Carrillo Pistons and Rods for VW/Audi

This piston and rod combination is designed as a perfect fit and meant to withstand large boost levels.

Getting Better Cylinder Head Airflow

When it comes to improving horsepower and rpm, airflow has a lot to do with it, and it seems the job is one that’s never finished.