Avoiding Workplace Accidents - Engine Builder Magazine

Avoiding Workplace Accidents

Shops can prevent many of these situations, along with the associated injuries that increase workers’ compensation costs and employee absences. If you walk around the shop and look with a critical eye, you can start reducing accidents today with some serious attention to detail.

You’re probably not going to cry over a little spilled paint, but will you or someone else in the shop literally take the fall for a co- worker’s carelessness?

In the shop environment, slips, trips and falls seem inevitable. The list of situations that can cause injuries is long: spilled paint, oil and grease; polished floors; loose matting and uneven walking surfaces; cluttered walkways and large equipment; electrical cords and air hoses; and ladders, scaffolding and stairways.

Because slips, trips and falls constitute the majority of workplace accidents, OSHA addresses general housekeeping as well as keeping aisles and passageways clear and free of hazards in its standards (29 CFR 1910.22[a] and [b]).

The good news, though, is that shops can prevent many of these situations, along with the associated injuries that increase workers’ compensation costs and employee absences. If you walk around the shop and look with a critical eye, you can start reducing accidents today with some serious attention to detail.

Cleaning Shop » A well-organized, clean shop promotes customer confidence and overall aesthetics, but it’s also good in the “preventing accidents” department. If your facility has poor housekeeping habits, you may be asking for trouble. A large number of slips and falls can be blamed on disorderly work environments.

Here are some examples:

  • ⁠Tripping on equipment or a tool that an employee forgot to put away.
  • Slipping on a paint, oil or grease spill that someone did not clean up.
  • ⁠Tripping on electrical cords or air hoses on the shop floor.

Cleaning up around the shop isn’t something that should only be done after hours by certain people. In fact, if employees clean up after spills, put tools away and move equipment to its proper place when they’re finished working with it, something else happens. Over time, your workplace establishes an environment of ownership, personal responsibility and employee pride. The behavior becomes a routine that’s simply done as part of each worker’s daily performance. When an individual is aware and automatically does his or her part to keep work areas clean, the result is a cleaner facility.

Yet, the nature of shop work often is that tools and equipment must be accessible, and normally this means they’re on the floor. Power tools must be plugged in, which means that cords can potentially create tripping hazards. To help decrease the chance of slips and trips, designate aisles and workspaces to help create a clear pattern for equipment and pedestrian traffic.

Keep in mind, however, that stacking boxes and equipment in aisles and hallways to get them out of the workspace is not good for business. Moving an obstacle from one bad place to another bad place isn’t an effective way of cleaning up the shop. Make sure that everything has a proper storage area and is moved there within a reasonable time.

Surface Challenges » Another challenge in shops where slips and trips are concerned is the actual flooring surfaces. From polished concrete floors to uneven surfaces, and matting to outdoor work areas, the number of different surfaces can create hazards in going from one place to another.

Traction on surfaces can change drastically when you factor in the environment. For example, customers and cars alike can bring the weather in to the shop with them, whether it’s tracking in water from rain or melting snow or ice dropping off vehicles. Smooth concrete that makes moving equipment easy can become a hazard to people walking back and forth, especially when workers don’t clean up spills quickly. Other fall hazards regarding specific surfaces include uneven floors and broken sidewalks, curbs and parking lots.

Shops can combat slips and trips because of surfaces by:

  • ⁠Keeping areas such as parking lots and sidewalks clean, clear and in good condition.
  • ⁠Using anti-skid adhesive stripping materials or anti-skid paint in areas that are frequently slippery.
  • Placing floor matting around doorways and other entryways.
  • ⁠Displaying wet floor signs in areas where a spill has occurred. This is especially important when a spill cannot be cleaned up immediately, or where the cleanup has just occurred but is not yet dry.
  • Encouraging employees to wear slip-resistant shoes.
  • ⁠Training and retraining employees.

Lackluster Lighting » Lighting is another shop component that should be addressed. The wrong type and number of bulbs can contribute to slips, trips and falls. Also, poor lighting can hide spills or wet areas. Keep these lighting tips in mind when assessing your workplace for fall hazards:

  • ⁠Inadequate lighting can hide dangers, especially in dim hallways or storage areas. Replace light bulbs when they fail, not when it’s convenient.
  • ⁠Repair fixtures and cords immediately if they malfunction; they’re not only a slip or trip hazard, but also can quickly become a fire hazard.
  • ⁠Make sure that stairways are illuminated properly.
  • Task lighting is important for workers who need additional lighting while working on vehicles.
  • Don’t forget emergency lighting. It’s important to maintain consistent lighting in emergency evacuation routing and to check these systems on a regular basis.

Summary » Though slips, trips and falls are a common occurrence in shops, they don’t have to be so frequent. Remember these tips to keep your shop orderly, organized and accident-free.

Article courtesy of BodyShop Business.

You May Also Like

HP Academy Teaches EFI Online

The HP Academy was started to fulfill the need for some sort of formal training for EFI tuning. Two New Zealanders, Andre Simon and Ben Silcock, founded HPA in 2010.

With the ongoing COVID-19 situation, classrooms, as we know them, are not in session. You can’t physically distance in a small class in real life, but you can online. Virtual learning is now the new norm across the country. The racing industry is getting a leg up thanks to one school that is dedicated to online education. 

Utilizing Instagram

“When we started, we had no business at all… that’s when I started using Instagram,” Yaghoubian says. “Back then I didn’t know a lot about social media, but it works for business really well, and especially the automotive industry on Instagram.”

Higher Revving Education

We’ve all seen the ads in magazines and online for schools, classes and seminars on tuning an ever-increasing number of engines and even transmissions in today’s cars and trucks. The better ones will include the use of a chassis dyno to show real-time results of the step-by-step methods they teach.

Chassis vs Engine Dyno

We spoke with a couple shops that utilize both dyno types to get their take on the advantages, disadvantages and reasons to have one over the other or both.

Tradeshow Season

While the rest of the world tends to slow down in the fourth quarter, our industry is starting to rev up. That’s because it’s tradeshow season, and the excitement for next year is always palpable!

Other Posts

The 12th Annual Race Track Business Conference Set for 2023 PRI Show

Officials with the National Speedway Directory have announced that the 2023 Race Track Business Conference (RTBC) will take place on Wednesday, December 6, at the PRI Show in Indianapolis, Indiana. Related Articles – Texas Motor Speedway’s Former President Eddie Gossage Has Died – IndyCar to Debut Hybrid Power Unit this Year – Summit Racing Announces

Tick Performance is Under New Ownership

Tick Performance, a performance parts manufacturer, has new ownership. New owners Joey Anderson and Matt Goins plan to continue manufacturing premium, American-made components at Tick’s North Carolina headquarters, picking up right where founder and former owner, Johnny Atkins, left off. Related Articles – Women in Motorsports North America’s Second Year SHEro Award – QualCast to

Automotive Specialty-Equipment Businesses Remain Optimistic Despite Supply Chain Issues

The record-high sales growth over the past two years for the automotive specialty-equipment industry is beginning to level off or subside, according to the newest SEMA market research report. Despite ongoing economic uncertainty, supply-chain issues, and rising costs, companies remain optimistic as sales remain solid and above pre-pandemic levels. Related Articles – Kingdon Drags Joins

Southern Style Racing Engines in Pinellas Park, FL

Southern Style Racing Engines (SSRE) & Components Inc., based in Pinellas Park, Florida, is for sale. Related Articles – Ned Walliser Elected WPI Board President – SCCA Event Schedule Now Available – Lauri Eberhart Named CEO at Friends of Laguna Seca Founded 50 years ago by current owner George Pils, SSRE is a fully equipped machine