Holley Sniper Stealth 4500 EFI Systems - Engine Builder Magazine

Holley Sniper Stealth 4500 EFI Systems

Holley/MSD has announce the release of Sniper Stealth 4500 EFI Systems, which are capable of supporting up to 1,500 horsepower for naturally aspirated engines and 1,250 horsepower for forced-induction applications.

Holley/MSD has announce the release of Sniper Stealth 4500 EFI Systems, which are capable of supporting up to 1,500 horsepower for naturally aspirated engines and 1,250 horsepower for forced-induction applications (comes with a 2.5 bar MAP sensor). Developed specifically to upgrade drag race and high-performance street vehicles to EFI, they feature eight 100-pound-per-hour fuel injectors and multiple input and output options to give you unlimited control of your engine.

You don’t have to be a computer genius to use the Sniper Stealth 4500 EFI System, and you don’t even need a laptop. A simple calibration wizard handles the initial setup – just answer a few basic questions about your engine, and the high-resolution full-color touchscreen wizard creates a base map and starts tuning completely on its own. The system even comes with a USB/CAN tuning cable for laptop tuning and free downloadable Sniper EFI software.

Fully compatible with both draw-through and blow-through forced-induction applications, Sniper Stealth 4500 EFI Systems are available in three different finishes – shiny, black, and gold. They feature integrated ignition timing control and a programmable launch control via a two-step and timing retard, either of which can be triggered by a trans-brake. It features -8AN fuel inlets, a Gen 3 Ultra Dominator-style four-bolt air cleaner flange, and 2.125-inch throttle plates that flow 1440 CFM for larger cubic-inch engines. There’s a built-in single-stage wet or dry progressive nitrous control and three programmable 0-5v sensor inputs for oil/fuel/dome, nitrous pressure, or any other critical information you select, and the included genuine Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel-map learning.

You May Also Like

Check Out What’s New at Dura-Bond Bearing

New transmission bearings, cam bearings and valve seat options.

We caught up Dura-Bond Bearing's Bill Dolak at the 2023 PRI Show to get a run down of what we can expect from the bearing company in 2024. Dura-Bond has new transmission kits, new cam bearings for the LS3 and Ford Godzilla engines, and a new copper-infiltrated powder metal valve seat, among plenty more.

ARP Special Chaser Taps

ARP has expanded its tap offerings to include some 22 different sizes.

ARP chaser taps
Summit Racing Forged Pro Pistons

Made in the USA, Summit Racing Forged Pro Pistons are made using ultra-modern technology and materials so they’re stronger and lighter.

CP-Carrillo Pistons and Rods for VW/Audi

This piston and rod combination is designed as a perfect fit and meant to withstand large boost levels.

Eneos Racing Pro 10w-50 Oil

With Racing Pro 10w-50, a 50/50 ester mix provides exceptional wear protection, extra high horsepower, and further anti-oxidation stability.

Eneos 10w-50 motor oil

Other Posts

Fluidampr Performance Damper for Mazda Miata

Fluidampr performance dampers protect your engine from destructive crankshaft torsional vibration.

Fluidampr Mazda Miata damper
Mahle PowerPak Pistons for 6.0L and 6.4L Powerstroke Engines

All four sets offer incredible versatility, allowing a daily driver to become a weekend warrior for drag, dyno, or pulling competitions.

Point One Small Block Chevy Head Stud Kit

Point One’s E190 head studs boast an impressive 190,000 psi nominal tensile strength.

Cadillac Supercharged LS engine
Weinle Motorsports Sheet Metal Intakes

These custom aluminum sheet metal intakes are built to your specs.