Two-Cylinder V-Twin Chevy Engine - Engine Builder Magazine

Two-Cylinder V-Twin Chevy Engine

Sometimes being a hoarder pays off. Johnny Gardner and his son were doing some spring cleaning in the shop and found a box of blown up small block Chevy parts. Not wanting to see the parts go to waste, it turned into a challenge to build something with them. The result was a one-of-a-kind two-cylinder V-Twin Chevy engine!

Engine of the Week is presented by

At Engine Builder, we get a decent amount of emails from readers. Folks like touching base with us to either give us praise for an article, ask us questions, sometimes express some displeasure (fortunately not often), but more than anything, they like to tell us what they’re working on. We’re always intrigued to know more, especially when the email subject line says, “Only one on the plant.”

A unique two-cylinder Chevy V-Twin engine

That was the email Johnny Gardner sent me about a month ago or so, referring to his two-cylinder V-Twin Chevy engine. He also piqued my interest even more with a photo of this one-of-a-kind engine build. We got to talking and Johnny told me about his background in motorcycles and race engines, and how this V-Twin build came about.

A sawsall cut the SBC block

“I have been riding motorcycles for 55 years,” Gardner says. “I’ve been building race engines, mainly dirt Sprint Cars, for 40 years. I build engines for racers, but not full time. I have a new 2,000 sq.-ft. shop in Little Rock, AR called the 31G Shop. We used to have two separate shops to house mine and my son’s race cars.”

Johnny’s full-time work was in repairing oil and gas equipment, but he always built race engines on the side in his spare time. He says he retired from his oil and gas repair work just a couple years ago.

“For most of my adult life, I’ve had a shop of some kind where I worked on our family race cars and built engines. It’s something I’ve always enjoyed doing,” he says.

The idea and the drive to build this unique two-cylinder V-Twin Chevy came from some spring cleaning at the 31G Shop.

“My youngest son worked with me for a couple of years in the shop,” he says. “While he was cleaning the parts room, he started to throw away boxes of blown up engine parts. With me being a mechanical hoarder, I came unwound and gathered all of it up like it was gold. He told me I would never do anything with the stuff, and I took that as a challenge.

“I thought about it for a while and then started looking on the web for modified Chevy small blocks. I found every kind of modified Chevy small block except for a V-Twin. I decided there should be one and so this build began.”

According to Gardner, the Chevy V-Twin build was an exercise in problem solving from start to finish. From cutting the crankshaft, camshaft, block, heads, blocking off oil and water passages, balancing the rotating assembly, timing the camshaft and the ignition – and that was just the start.

“For this project, I did all the design, machining, painting, assembly, including the engine balancing in-house,” he says. “The only thing I didn’t complete myself was the leather covering on the seat. The block was initially rough cut with a sawsall, then I machined it to finished dimension in a Bridgeport mill. The crank and head were cut in a band saw and the heads were finished on the mill. Then the crank was finished on my lathe.”

The engine block is a stock Chevy with Milodon main caps. The crank and rods are aftermarket parts. The pistons are from JE and the rings are from Total Seal. The bearings in the engine came from Clevite. The cylinder heads were made from a single Brodix ASCS spec head.

“On the head, the middle cylinders were messed up,” he says. “It was cut so that the two ends of the cylinder head were used. I also used a Wulff dry sump oil system and a Shaver-Wesmar gear drive with a Huggins camshaft, stainless valves, and roller rockers. The fuel injection is Hilborn and uses alcohol.”

The Huggins cam was the same as what Gardner would use in one of his Sprint Car engines. It is .665 lift with 292 duration at 106. As for the bike itself, Johnny says it was built to be a cool display stand for the engine more so than a rideable bike. 

“It was built from old Sprint Car parts,” he says. “It uses a splined rear axle, brakes and rotors, and the front and rear wheels are from a Sprint Car too. The engine is a structural part of the frame, which was made from 1 3/8˝ Drawn Over Mandrel (DOM) tubing. The frame, like the engine, is a one-off build. Every part of it is unique, except for the 748 Ducati front forks. The bike is rideable, but I have to admit it is scary!”

Gardner estimates the bike weighs around 400 lbs., and the full build took him about a year and a half from the time he started doing drawings to figuring out how to go about it to the finished bike. He was also still running his business and racing a Sprint Car full time during the build.

The two-cylinder Chevy V-Twin engine makes an estimated 180 horsepower, and Gardner plans to do some dyno runs soon. The headers are handmade from bends bought from Speedway Motors using a case backhoe turnout on the end.

“I made or modified every piece on this thing. It’s the only one on the planet,” Gardner says.

We have to admit, this V-Twin build is awesome, and we’re glad Johnny decided to make the first of its kind, and share the details of it with us! Hear it start up below!

Engine of the Week is sponsored by PennGrade Motor OilElring – Das Original and Scat Crankshafts. If you have an engine you’d like to highlight in this series, please email Engine Builder Editor, Greg Jones at [email protected].

You May Also Like

Supercharged 388 cid LS Engine

Hoping to reach new heights in the mile, this Cadillac customer brought his car and engine in for the School of Automotive Machinists & Technology to work their magic on. See what went into the supercharged LS engine platform.

Cadillac Supercharged LS engine

During our week in Houston last fall, we got the chance to visit several engine shops in the area, and we also wanted to spend some time seeing where many up-and-coming engine builders get their start and hone their skills, so we stopped by the School of Automotive Machinists & Technology, also known as SAM Tech.

Supercharged 521 cid Brad Anderson Hemi Engine

Amanda Hoover and Eddie Rogers have been campaigning their Chevelle from Hell for nearly a decade. Helping give the car its name is a screw-blown 521 cubic inch Hemi engine. Check out the details of this build done by Chris Duncan Race Cars!

408 cid Nitrous LS Engine

During a tour of SAM Tech, we also got a chance to speak to a few students. One in particular, Jaylon Victorian, was nearing completion of a 408 cid nitrous LS engine. He applied his new engine building knowledge and skill set to the build, and it shines through in our latest Engine of the Week.

408 cid nitrous LS engine
760 cid Billet Big Block Chevy Nitrous Engine

Despite what you may think about nitrous engines, and those that are stock big block Chevy bore spacing, these 4.840″ bore space big block Chevy engines have some significant R&D in them. Just check out this 760 cubic inch billet version done at TRE Racing Engines.

Naturally Aspirated 440 cid LT1 Engine

The folks at Late Model Engines in Houston, TX run a top-notch engine and machine shop. You don’t have to look much further than this naturally aspirated 440 cid LT1 engine build to see what we mean. It’s our Engine of the Week!

Other Posts

Steve Morris Engines’ Twin-Supercharged 454 Big Block Chevy Engine

It had been 26 years since the last time Val Morris, Steve Morris’ wife, was behind the wheel of a drag car. The shop had been working on this project car named Sugar Momma, and got it done in time for Sick Week 2024. When it came time to figure out who’d drive it, Steve

Factors of Crankshaft Selection

From the high-performance powerplants propelling Top Fuel dragsters to the subdued engines found in family sedans and grocery getters, each crank must be tailored to, and appropriate for, its specific application.

Stuffing a Supercharged 572 cid SMX Engine in a Porsche 928

For Danny Humphreys, drag racing is a progressive disease. Ever since he watched Tom Cruise outrun a pimp in a 928 Porsche, he’s wanted the car for himself. As soon as he got one, he pulled the engine and the horsepower has gone up from there. Today, Danny has a supercharged 572 cid SMX engine

B&B Performance Adjustable Billet Timing Pointers

Available for SBC, BBC and SBF, pointers come with stainless steel pointer, fasteners and a black anodized finish.

timing pointers