Haas Automation Hosts National
On October 10, 2012, Haas Automation, Inc., will “Illuminate the Latest Haas Turning Technology” during a national Demo Day at more than 40 Haas Factory Outlets (HFOs) throughout the United States and Canada. The Haas ST series Y-axis turning centers provide 4" of Y-axis travel (±2" from the centerline) for off-center milling, drilling, and tapping,
Supplier Strategies for Web Success
“Virtual education” is one of the hottest trends out there in the educational community, thank to the ability to provide real-time communication between teachers and students. Many public schools allow students to bring smart phones, tablets and laptops to class to facilitate the transfer of information and enrich the learning experience. If you think about
Pneumatic Tool Innovations
Pneumatics is that section of technology that deals with the study and application of pressurized gass to affect mechancial motion. Or, said differently, pneumatic tools use compressed gas (usually air) to make them work. I would venture to guess that most, if not all, of you reading this use air tools frequently, or have used
Engine Builder Shop Solutions: August 2012
Editor’s Note: This coming October will mark “Shop Solutions’” fifth anniversary and to help Engine Pro celebrate, we’re putting plans into place to have a “Top Five from the Past Five” contest where you’ll get to choose your favorite Shop Solution from the past five years. Watch this section as well as the magazine for
New Rear Main Seal Installation for 1995-2004 GM 3.8L Engines
Affects 1995-2004 GM models with with 3.8L V6 Engines (VINs K, 1,2, 4 – RPOs L36, L67, L26, L32) Crankshaft Rear Oil Seal and Housing Removal 1) Remove oil pan assembly as outlined in the appropriate Service Information Manual. 2) Remove the crankshaft rear oil seal housing bolts. 3) Remove the crankshaft rear oil seal
COMP Cams Engine Builder Duel Returns To NSRA Street Rod Nationals Aug. 2-5
The 2012 NSRA Street Rod National participants will get a chance to showoff their engine building skills in the COMP Cams Engine Builder Duel this weekend, Aug. 2-5, at the Kentucky Exposition Center in Louisville,KY. The event annually features over 11,000 street rods and more than 30,000 visitors. The Engine Builder Duel, presented by Snap-On
A&A Midwest Welcomes Leonard O’Connell as New COO
After a national search, Leonard "Len" O’Connell, a veteran automotive aftermarket leader, has joined A&A Midwestas chief operating officer (COO). In this newly created position withinthe 63-year old privately held, family company, O’Connell will be basedat the A&A Midwest Chicago location. All company managers now report to O’Connell, who has taken over the day-to-day
Cylinder Head Resurfacing Tips: How To Produce An Ideal Surface Finish
Dress and true the wheel Always dress and true the resurfacer wheel face to keep it in propergrinding condition. Never dress or true a wheel above the wheel centerline. In addition, always dress or true the wheel as close as possibleto the point of actual grinding. Since the grinding wheel usually wearsmost often on the
MAHLE Clevite Expands Online Gasket Data Utilizing OptiCat
Victor Reinz gaskets have always been available for applications dating back to 1942, however, only applications from 1990 and newer were available electronically, the company points out. The increase, which includes more than 9,000 unique part numbers for applications from 1942 to 2013, more than 75,000 vehicle engine combinations and coverage for more than 211
Giving Away Profits To Stay Busy Makes No Business Sense
Why am I writing about your wallet? To be perfectly honest, it’s because I want you to stay in business. If you’re not in business, Engine Builder magazine isn’t in business. If you’re not in business, Goodson Tools & Supplies isn’t in business. If you’re not in business, Dave Monyhan is not employed, and that
Performance Oil Systems
For the engine to survive, the oiling system must be capable of supplying an adequate volume of oil under a wide range of operating conditions. The oiling system must also maintain adequate pressure to keep the oil flowing to all of the places where it is needed. Critical among them are the crankshaft and camshaft
Still Time to Register for AERA’s Tech & Skills Regional Conference in Denver
Everyone owes it to themselves and their business to gain knowledge and network with other people within the same industry. AERA understands that traveling to national trade shows to gain this knowledge and networking opportunities is very expensive. Therefore, AERA has decided to help by teaming up with a regional host and offer these opportunities
Engine Builder Shop Solutions: June 2012
Reducing Vibrations And Chatter Vibrations when machining with extended length setups can not only cause chatter and premature tool failure, but also reduce spindle bearing life and lead to poor surface finish, dimensional control issues and premature tool wear. Shops are often forced to reduce cutting parameters to avoid chatter, decreasing productivity. Chatter occurs when
How to Properly Dress Crankshaft Grinding Wheels
The grinding wheel must be dressedeach time it is placed on the machine, even though it may not have beenremoved from the wheel center. Mountthe wheel dresser on the grinder table. Bring the rotating grindingwheel up close to the diamond and start the coolant flow. Never dresswithout coolant. Frictional heat buildup can cause the diamond
Leading By Example: Focus On Core Strengths To Build A Stronger Team
He had a lot of time to reflect on life and who he was during his long stay at the South Pole Advance Base weather station in 1934, where temps averaged -60 degrees in the winter. He was alone and the closest human was 123 miles away. Segueing from that example, in this article I’d
Liberty Engine Parts to Host Next AERA Regional Conference
AERA says engine builders can gainindustry knowledge and network with other people with the traveling expense ofgoing to a national trade show. AERA has teamed up with a regional host tooffer opportunities in different regions of the country that is closer to anumber of shops. Along with the outlined technical programs, AERA has invited leadingmanufacturers
AERA President John Goodman Announces Retirement
After 9years at the helm, Engine Builders Association (AERA) President John Goodmanhas announced his retirement, effective July 1, 2012. “John became president of AERA in October of2003 rejoining an industry that he had briefly left to finish his Ph.D. inEngineering Management,” explained Jim Rickoff, associate editor of EngineProfessional and AERA’s marketing consultant. “At AERA, John
3-angle Seat Cutting Tips
Goodson Tools and Supplies for Engine Rebuilders suggests using Carbide Pilots for precise and high-quality valve seat and bowl work. 1. Carbide pilots offer the following advantages: Carbide Pilots help keep tooling cutting true. When cutting 3-angle seats, counterboring for seat rings or using Bowl Hogs to enlarge valve bowls, the resistance of the workpiece
Big Block Chevy Cam Identification
While turning the distributor during diagnosis process your customer noticed the other four cylinders would start running and theoriginal four go dead. Now, since it is a big block I truly understooda phrase that my brother always used: "There is no substitute for cubicinches," because it did actually run on either of the four cylindersets.
Rear Main Oil Seal Installation Tool Caution for Suzuki Engines
Affected Model/Engine: 1996-1998 Sidekick Sport 1.8L; 1999-2003 Vitara (SQ420), Grand Vitara (SQ625), XL-7 (JA627); and 2002-2003 Aerio (RH420) engines. CONDITION: Repeat Rear Main Oil Seal Replacement. CAUSE: The proper installation tools are not used to install seal. CORRECTION: Use the recommended oil seal guide and installer as referenced in the applicable service manual. (See illustration)