Engines Market: Total Engine Production Generated By Manufacturers In The U.S. And Canada Increased in 1996
Annual production of remanufactured enginesclimbed from 1.32 million in 1995 to 1.57 million during 1996– an increase of about 19.4%. Engine production figures are based on a universe of 120 U.S.and Canadian rebuilders that rebuilt an average of 13,113 short,long and complete engines each last year. Survey results werecompiled from a detailed questionnaire mailed to
Electrical Market The Market For Rebuilt Starters And Alternators Has Been Painfully Soft
So far this year, the market for rebuilt startersand alternators has been painfully soft for many rebuilders. Ina business that depends heavily on the weather to stimulate sales,a mild winter and a relatively cool spring and early summer havedone little to spur demand. For most rebuilders, sales have beenflat. In some areas of the country,
Clutch Market: Passenger Car And Light Truck Clutches
Optimism isn’t exactly running high these daysamong clutch rebuilders and their component parts suppliers, particularlywith respect to passenger car and light truck clutches. The marketis being squeezed on one side by an influx of new clutches fromoffshore suppliers, and on the other side by price pressures andtoo much competition. You might say it’s a gripping
Brakes Market: Brake Rebuilders Have No Intention Of Slowing Down
Despite a few bumps in the aftermarket roadto success, brake rebuilders have no intention of slowing down.Some brake industry professionals say that demand in the brakerebuilding market is pretty consistent compared to last year. "The market (in sales) seems to be following the same patternsas last year," said Steve Suber, friction materials managerfor EIS Brake
Machine Shop Market Profile Part II
Based on information provided in part one ofour annual Machine Shop Market Profile which appeared in lastmonthís issue, the machine shop market produced between1.31 million and 1.7 million rebuilt engines in 1996. These figuresrepresent a decline of about 7% from the previous production year. Part one of our annual Machine Shop Market Review featured detailson
Ensuring Bearing Life: Crankshaft Bearings Are Always Replaced When Rebuilding An Engine
Crankshaft bearings are always replaced when rebuilding an engine because they’re a wear component. Heat, pressure, chemical attack, abrasion and loss of lubrication can all contribute to deterioration of the bearings. Consequently, when an engine is rebuilt new bearings are always installed. “Reading” the old bearings can reveal a great deal about conditions that may
Piston Rings and Surface Finish
Horsepower is always paramount in the minds of customers who salivatelike a Pavlovian dog when the terms "high performance"and "engine" are used in the same sentence. Unquestionably,horsepower is heady stuff, capable of not only moving a vehicleto obscene speeds, but also of propelling its owner to a positionof prominence in the eyes of performance enthusiasts
Machine Shop Market Profile
As is generally already known, the machineshop/custom engine rebuilder market struggled in 1996 to keeppace with production numbers generated in 1995. Many shop ownerstold us that demand was flat for machine shop services and/orrebuilt engines during 1996. Verification of these shop owners’ commentswas generated in our annual survey of the membership of the AutomotiveEngine Rebuilders
Making A Big Splash In The Marine Market
The average individual that would have owned a performance car in the 1960s, and the baby boomers that did, in many cases no longer have a modern affordable toy they can tweak to their own satisfaction. Serious performance today is often available to only a few with large checking accounts or extra good credit, and
Rebuilt Market Reviews – Engines Market
Total engines remanufactured by all production engine remanufacturers (PERs) in 1995 increased a modest 3.5%, growing to 1.318 million units last year compared to 1.273 million units produced in 1994. Production totals are based on a U.S. and Canadian universe of 120 PERs that produced an average of 10,609 remanufactured engines annually in 1995. Survey
Rebuilt Market Reviews – Brakes Market: Rebuilders And Suppliers Chant The Same Mantra
When it comes to current trends in the brake rebuilding market, rebuilders and suppliers chant the same mantra – “price” and “quality.” Both are the primary forces driving parts and equipment suppliers’ and rebuilders’ business. Consumers demand the best performing materials, but of course, at the lowest possible price. Unfortunately, say many rebuilders and their
Perspective On Using CBN Versus Polycrystalline Diamond (PCD) Cutters
In your June Shop Line you offered Jerry Lawson’s of DCM Tech, Inc., perspective on using CBN versus poly crystalline diamond (PCD) cutters. Have any other manufacturers voiced their opinions? In PERA’s May 1996 Current Concerns publication, Andy Rottler of Rottler Manufacturing made the following observations on CBN versus PCD cutters:Rottler says that due to
Letters: Test Data For Failing Rectifiers Requested
The article by Donald Yuhas, “Dissecting CS-130 Diode Failure,” in the May, 1996 issue of Automotive Rebuilder gave electrical rebuilders insights into the ways that diodes can fail. The author concluded that high “current pulse” technology is needed for successful screening-out of diodes that will likely fail in the vehicle.While I share that conclusion, the
The 1995 Camaro That Served As The Basis For Project Road Rocket
As noted previously, the 1995 Camaro that served as the basis for “Project Road Rocket” received a change in rear end gearing and that, in combination with the repair of an exhaust system leak really brought the car to life.From a best quarter-mile performance of 12.87 at 109.27 miles per hour the Camaro blasted to
Caliper Clinic: Rebuilders Not Only Can Improve An OE Design, But They Can Also Improve The Consumers’ Opinion
Rebuilders not only can improve an OE design, but they can also improve the consumers’ opinion about the rebuilt auto parts business, in general. Many people still believe that all rebuilt parts are sub-standard compared with original equipment parts. However, most rebuilders are continually working to improve the reputation of rebuilt parts by producing quality
Complete Circuit: The Components That Are The Cause Of Most Starter Failures
If you had to categorize the components that are the cause of most starter failures, the starter solenoid, without a doubt would be on top of the list. The starter drive may come in a close second. Some large rebuilders may opt to rebuild their starter solenoids in-house or have them built to their specifications,
Eis Brake Parts: Consists Of Five Separate Remanufacturing Facilities In The U.S. And Canada
EIS Brake Parts has come a long way since it began as a manufacturer of hydraulic brake hose couplings back in the early 1930s. Today the company, which became a division of Standard Motor Products in 1986, consists of five separate remanufacturing facilities in the U.S. and Canada. The facilities are located in Berlin, CT;
Grinding Techniques: In Thousands Of Years, The Basics Of Grinding Haven’t Changed
Grinding is one of the oldest methods known for shaping and sharpening objects. It was first used in prehistoric times to make weapons and other tools by rubbing wood, stones, bones and eventually metal against hard, abrasive rocks. In thousands of years, the basics of grinding haven’t changed. We’re still rubbing an abrasive against metal
Cv Market Travels Fast Track: Power To The Front Wheels Is The Drive System Of The Present And Future
Although sport utility vehicles, many still with rear wheel drive, are the hot sellers right now, few will dispute that power to the front wheels is the drive system of the present and future. A market for rebuilt front wheel drive axles and CV joints will be around for a long, long time. With few
Engine Installation – A Growing Opportunity?
Engine rebuilders who are looking to expand their share of themarket may want to consider engine installations. Although somerebuilders may think installations are better left untouched,others are finding installations provide a profitable niche ina competitive market. Terry O’Donnell, manager of RPM Engines andMachines, Rohnert Park, CA, is just one of many rebuilders inthe industry who