Tech Solutions Guide
February 2007 Tech Solutions Guide Index of Technical Bulletins Chrysler Ford Diesels GM Imports Sponsored By:
Engine Builder Shop Solutions, December 2007
Piston Rings 101: Proper Break-In If piston rings are not properly broken in, the result may be excessiveoil consumption. Compression rings rely on combustion pressures toforce them down against the bottom of the ring groove and out againstthe cylinder wall. This is what makes the rings seat and seal. Initialring tension accounts for only a
Shop Solutions: November 2007
Solution for Pre-mature Camshaft Failure on Big Block Chevy Engines ≈Big Block Chevrolet engines are well known for being subject to premature camshaft lobe wear and failure. Here are ways to help relieve this problem. When replacing a hydraulic camshaft, instead of using the OE type of lifter (p/n 817 or VL37) use p/n 2095
New Metals-New Challenges
Cast iron is like an old familiar friend to most of our readers because it’s been around forever. Vehicle manufacturers like cast iron because it’s cheap compared to most other metals, it is strong and durable, and it can be easily cast and machined to make engine blocks, cylinder heads, crankshafts, connecting rods and other
November 2007 Engine Rebuilding Technical Guide
Ford 347 Stroker Chrysler 2.4L GM 6500 Optimizer Brought to you by:
Coretalk: Performance Marine Industry Expo To Launch In Las Vegas
The theme of the show is “Experience the Power, the Passion and the Performance.” Consumers will be able to see boats in action at Lake Mead, performance test new boats and test boats they purchased at the show. Performance Marine Industry Expo is the result of ConvExx, producer of the internationally acclaimed SEMA show, teaming
Coretalk: Key Industry Speakers Slated For PERA’s Chicago Convention
Yastrow and Som will discuss “Current Issues in Employment-Related U.S. Immigration Law: I-9 Compliance, Visa Updates.” In addition to addressing hot topics and compliance tips, they will provide answers to your specific questions.Bob McKenna, President/CEO of Motor & Equipment Manufacturers Association (MEMA) and Past President of NAPA, will be speaking on “Motor Vehicle Parts Suppliers
Coretalk: Chicago To Host PERA’s 62nd Annual Conference September 27-29, 2007
An assortment of professional and technical seminars will be held along with a wide range of social and networking opportunities for engine remanufacturers and their spouses. For more information on this event or to register for the convention, visit www.pera.org. Recon Launches Plan To Increase Availability and Reduce Delivery Times Recon Automotive Remanufacturers has announced
Coretalk: Pro Motor Engine Team Sets Clevite Showdown Record To Win Finals
>Borem and Hoffman, who had an engine-build time of 16 minutes and 25 seconds, with no penalties, went head-to-head with Hendrick Motorsports’ Kevin Webber and Scott Vester, who finished second with a build time of 17 minutes and 47 seconds with no penalties. For their efforts (the third fastest build time overall), Webber and Vester
Dialing in on Today’s Engine Bearing Trends
Durability is less of a concern today because the aftermarket and OEMs demand bearings that can last 150,000 miles even under severe stress from a neglectful vehicle owner. In performance applications there are a number of materials that will do the job well. Each material has its advantages in terms of resistance to corrosion, rate
GM’s 6.5L Diesel Engine
The 6.5L GM diesel engine was introduced in 1992 to replace the 6.2L diesel engine and was in turn replaced by GM’s Duramax 6600 in 2001. On the surface it would appear that the story of the 6.5L diesel would end here, right? Well, that wouldn’t make much of an article. In actuality, production of
Coretalk: Maxiforce Makes List Of Top Minority-Owned Businesses In Miami
“It’s a fantastic honor to be distinguished among so many impressive minority-owned enterprises in this city,” said Santiago Morales, CEO of Maxiforce. “We have always strived to understand the needs of our customers in both the United States and around the world, and we believe these awards underscore the importance of such efforts.” Specializing in
Coretalk: Engine Builders Asked To Show ERC Support on Business Web Sites
The Web site contains a variety of tips, articles and other tools aimed at consumers seeking information about engine repowering. An update of the site’s engine installer and remanufacturer/rebuilder shop finder service is still under construction. “We need to get more engine builders and installers to get involved with ERC so that customers can easily
Rebuilding The Chrysler 2.4L
Chrysler replaced its old SOHC four cylinders with an all-new family of SOHC and DOHC engines in 1995. There were 2.0L SOHC and DOHC versions, along with a 2.4L DOHC that was installed in the FWD cars and minivans. Add seven different head castings that came with and without EGR and A.I.R. and throw in
Coretalk: Clements Racing Engines Receives First PBM Engine Builder Award
PBM’s Kevin Harrison made the presentation at the Speedway Club at Lowe’s Motor Speedway during the series’ 2006 Awards Banquet. Clements Racing Engines led the series with 10 victories on the season. Among the drivers visiting victory lane with Clements power under the hood were Ricky Weeks, Jack Pennington, Noel Tucker, Royce Bray, Ed Basey
Coretalk: Nashville Sheraton Site For PERA’s Spring Tech
The meeting, a combination of technical sessions and hands-on demonstrations, presentations and a facility tour, will begin on Thursday, March 22 at a special reception in the hotel’s Pinnacle Room. NHRA Top Fuel drag racer Hillary Will is scheduled as the reception’s special guest. The technical program will begin on Friday morning following breakfast hosted
Pistons and Pins: What’s New
Asking piston manufacturers “what’s new” reveals a number of trends that are reshaping the piston business today. One is that there’s no longer a time lag of three or four years for aftermarket piston suppliers to tool up for the latest piston applications. Production engine remanufacturers (PERs) and custom engine rebuilders (CERs) are asking for
February 2006 Tech Solutions Guide
FORDsponsored by CHRYSLERsponsored by GMsponsored by IMPORTsponsored by DIESELsponsored by
Ward’s Auto World Names 12th Annual ‘Top 10 Best Engines’
Ward’s Auto World Names Twelfth Annual ‘Top 10 Best Engines’ The winners of “Ward’s 10 Best Engines” awards for 2006 demonstrate U.S. auto consumers still can have it all: many of the winning engines highlight sophisticated new technology that generates exhilarating performance – but also improves fuel economy. The 2006 list marks the 12th year
High Performance Piston Rings and Cylinder Finishes
Today’s performance ring sets are thinner, lighter and more conformable than ever before. Thinner, low-tension rings reduce friction for more usable horsepower. Less weight reduces ring groove pound out. Narrower rings also allow tighter tolerances and less blowby. All very good things when you’re building a performance engine. But they also require rounder, straighter cylinder