Increased crankshaft journal dimensions for 1995-2002 Kia 1.8L VIN 5 engines.
Engine Builders: The AERA Technical Committee offers the following information on increased crankshaft journal dimensions for 1995-2002 Kia 1.8L VIN 5 engines. The main journal diameter for the crankshaft of this engine was increased beginning with the 1998 model year. Mazda manufactured these engines prior to 1998 while Kia manufactured all subsequent engines. Use caution
Cylinder head bolt replacement for 1997-2003 Ford 6.8L VIN S engines.
Engine Builders: The AERA Technical Committee offers the following information regarding cylinder head bolt replacement for 1997-2003 Ford 6.8L VIN S engines. This engine requires new replacement cylinder head bolts any time the head is installed. Follow the procedure listed below after all components have been thoroughly cleaned and prepped. Ensure that all surfaces of
Cylinder head stress plate for Caterpillar 3126 diesel engines.
Engine Builders: The AERA Technical Committee offers the following information regarding a revised cylinder head stress plate for Caterpillar 3126 diesel engines. Previously AERA published Technical Bulletin 1561 concerning a stress plate for this engine. The previously made plates covered a single cylinder and required multiple relocations of the plate to bore/hone all six cylinders.
PERA’S Core Corner
This month we are going to look at some issues that have certainly been identified in previous issues of Engine Builder. However, based upon the number of recent inquiries at PERA headquarters we thought it might be a good time to bring them to everyone’s attention again as a helpful reminder. First, is the 2.9L
The lower intake manifolds on some Ford vehicle models are not fitting correctly after machining
Engine Builders: Some AERA members have reported that the lower intake manifolds on some Ford vehicle models are not fitting correctly after machining. To reduce the likelihood of coolant contamination of engine oil, a revised, thicker intake gasket is now available for the 3.8L and 4.2L Ford car and truck engines. These models have VIN
Conferences And Seminars Offer Many Potential Rewards
Getting away from the day-to-day grind and going to a seminar or conference with fellow shop owners and machinists has rewards that far outweigh the expense, and often may even present new business opportunities. At the Engine Rebuilders Association Tech Expo (AERA) I attended this past April in Indianapolis, a presentation given by John DeBates,
Repair Of Worn Cam Bearing Housing Bores For Detroit Diesel 11.1l And 12.7l Diesel 60 Series Engines
Engine Builders: The AERA Technical Committee offers the following information regarding the possible repair of worn cam bearing housing bores for Detroit Diesel 11.1L and 12.7L diesel 60 Series Engines. These engines use an overhead camshaft design with seven individual location precision bearing inserts. Over time, the bearing bores may become worn oversize or out-of-round,
1997-2002 GM 4.8, 5.3, 5.7 & 6.0L VIN V, T, G & U engines
Engine Builders: The AERA Technical Committee offers the following information for 1997-2002 GM 4.8, 5.3, 5.7 & 6.0L VIN V, T, G & U engines. These engines were manufactured with two different design connecting rod bolts beginning in 1999. Either design bolt, when used in pairs and properly tightened, may be used on a single
Eliminate head gasket failures on Cat diesels
Q. To eliminate head gasket failures on Cat diesels, how should the heads be torqued? A. Pressurizing the cooling system with the oil pan removed can differentiate between a water pump leak and a cylinder head gasket leak before removing the head. If a head gasket is the source of the problem this revised cylinder
Revised cylinder head installation procedure for 1997-2002 GM 5.7L VIN G engines
Engine Builders: The AERA Technical Committee offers the following information on a revised cylinder head installation procedure for 1997-2002 GM 5.7L VIN G engines, Figure 1. This revised procedure should be used any time the cylinder heads are being installed and supersedes information found in earlier published service manuals. Previously published technical bulletin TB 1624
Rebuilding the Ford 4.6L SOHC Engine
The 4.6L was lower, shorter and lighter than the 302, but the base engine made more power than the 302, got better fuel economy and passed all the emission tests without a thermactor pump. Ford called it its “modular” engine because it was part of a whole new family of engines that were intended to
A Kubota diesel engine for rebuild
Engine Builders: If you are considering a Kubota diesel engine for rebuild, the following specifications regarding compression pressures will be helpful. For your installer customers, this information will be useful in engine diagnosis. To obtain an accurate value of cranking compression, the engine should be operated until normal operating temperature is reached. If an engine
Dirt Track Dollars In the Shop and On the Track With Malcuit Racing Engines
It’s sometimes said that racers have motor oil or high octane racing fuel in their blood. Fearless drivers are accused of having ice-water running through their veins. For Strasburg, OH’s Brad Malcuit, the most likely ingredient pumping through his bloodstream is dirt, a fact he’ll happily attribute to family heritage. Malcuit is owner of Malcuit’s
Engine Sludge Origins
Fresh engine oil is a clear, free-flowing liquid blend of base stock and additives that contains no fuel, water, coolant, dirt, or other contaminants. When regular engine oil changes are neglected, normally free-flowing lubricating oil breaks down, becomes contaminated, ceases to flow, and is transformed into a thick soup of waste products. That’s when
Rebuilding The Ford 3.8L Engine
They needed an economy engine that would fit in their new cars, and they needed it fast. They had a couple of old inline sixes and a small German V6, but none of them were designed for fuel economy or the coming emissions standards, and the 250 cid engine was so tall that it wouldn’t
Ford 4.0L V6 Engine
The original 2.6L engine was replaced by the 2.8L, which was upgraded to the 2.9L and then finally bored and stroked to make it into the 4.0L that was used in the Rangers, Aerostars and Explorers starting in 1990. It was replaced by a SOHC engine from this same family at the end of model
Torque-to-Angle/Yield Threaded Fasteners
All the original equipment manufacturers (OEMs) have fastener labs with lots of sophisticated equipment and well-educated people working on fastening issues. They even have their own professional association – The Bolting Technology Council – which holds meetings and seminars about fasteners. I’m not a fastener engineer, and I’m not going to make you into one.
Threaded Fasteners Torque-to-Yield and Torque-to-Angle
All the original equipment manufacturers (OEMs) have fastener labs with lots of sophisticated equipment and well-educated people working on fastening issues. They even have their own professional association – The Bolting Technology Council – which holds meetings and seminars about fasteners. I’m not a fastener engineer, and I’m not going to make you into one.
Heavy Duty Details: Damaged Main And Cam Bearing Saddles Can Be Successfully Repaired By Sleeving
The process is relatively easy to accomplish, and the repair is reliable How many times have you seen a block that is discarded because of damaged main saddles or cam bearing saddles? Numerous individuals try to have the block brazed or welded and then align bored. Because blocks require that they be completely heated to
Engine Cylinder Bore Surface Finishes
What’s the best type of cylinder bore finish for today’s engines? Most would say it’s a finish that allows the rings to seat quickly and completely so the engine doesn’t use oil. For many applications, that may mean a plateau finish. The surface finish must also meet the piston ring manufacturer’s specifications and have the