The Future Of Boring Is Exciting
Boring out cylinders to accept oversized pistons or sleeves has long been a common practice in the engine rebuilding business. Boring allows worn blocks to be salvaged, and stock cylinder bores to be enlarged for more displacement. More recently, boring is also being used to install special cylinder liners with hard surface treatments in high
Improving engine balance on 1992-2001 GM 6.5L VIN 7, F, P, S and Y diesel truck engines
Engine Builders: The AERA Technical Committee offers the following information on improving engine balance on 1992-2001 GM 6.5L VIN 7, F, P, S and Y diesel truck engines. This information should be considered any time this engine is remanufactured. While some owners of these engines have accepted the original driveability condition as normal, others have
Rebuilding The Ford 3.8L Engine
They needed an economy engine that would fit in their new cars, and they needed it fast. They had a couple of old inline sixes and a small German V6, but none of them were designed for fuel economy or the coming emissions standards, and the 250 cid engine was so tall that it wouldn’t
Coretalk: September 2001
Ford Plans to Revamp Parts Distribution Network Ford Motor Co. is working to restructure and expand its United States parts distribution network to deliver service and repair parts to its dealers faster and more efficiently. Over the next three years, Ford plans to increase the number of parts distribution centers from 10 to 21, creating
Back to Basics: Preventing Piston Problems
Burned pistons. Scuffed pistons. Cracked pistons. These are problems no customer wants to experience in an engine you’ve built. Warranty claims can kill your business, so here are some tips on how to prevent these and other common piston problems. First and foremost, if you’re custom building an engine that has already suffered some kind
Rebuilding the New Chevy 262
This enabled GM to shorten the development process dramatically because it was able to adapt a proven design. But it also allowed it to share a lot of the existing tooling from the V8 production lines so the engines could be on the road sooner. The original 200 V6 that came out in 1978 was
Rebuilding the Chevrolet LT1 Engine
Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20 percent more horsepower, got better fuel mileage, and had a much broader torque band with 90 percent of its peak torque available from just over 1,000 rpm all the way up to nearly 6,000 rpm. GM Powertrain accomplished all of this by
Rebuilding the Chevrolet LT1 Engine
Although it shared many common dimensions, looked much the same and even had a few common parts, it was totally redesigned to provide more power with lower emissions and better fuel economy. Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20% more horsepower, got better fuel mileage, and had a
Rebuilding The GM Quad 4
The Quad 4 had four valves per cylinder, tuned intake and exhaust manifolds, no distributor, no plug wires, lightweight rods and pistons to reduce shaking forces, and a crank with eight counterweights that was designed to reduce noise, vibration and harshness (NVH) and bearing wear. It didn’t have an A.I.R. pump or an EGR system,
In Pursuit of Quality: Tom Vecchi, Engine Supply, Inc. incoming PERA president
Tom Vecchi, president of Engine Supply, Inc.,Phoenix, AZ, and incoming president of the Production Engine RemanufacturersAssociation (PERA) hasn’t spent his entire business life in theengine rebuilding market. However, since acquiring Engine Supplyin 1988 with his brother-in-law, Len Joy, who is chairman of theboard, he’s learned enough to know that rebuilding engines isnot an easy way
Why Parts Get Coated
I never would have believed you could get those kind of resultsfrom a glorified paint job. With those words, another skeptic(in this case, a NASCAR Winston Cup engine builder) had come toaccept the value of special coatings applied to engine components. At the time, such skepticism was not totally unwarranted. Likeany emerging technology, the coating
Valvetrains: Better Materials & Design
Pushrods would seem to be an endangered species these days, atleast as far as most new engine designs are concerned. The onlybrand new engines built in recent years with a pushrod valvetrainhave been Chrysler’s 8.0L V10 for the Viper and Dodge Ram, andGeneral Motors new "LS1" 5.7L small block V8. All therest have either been
Brakes Market: Brake Rebuilders Have No Intention Of Slowing Down
Despite a few bumps in the aftermarket roadto success, brake rebuilders have no intention of slowing down.Some brake industry professionals say that demand in the brakerebuilding market is pretty consistent compared to last year. "The market (in sales) seems to be following the same patternsas last year," said Steve Suber, friction materials managerfor EIS Brake
Piston Rings and Surface Finish
Horsepower is always paramount in the minds of customers who salivatelike a Pavlovian dog when the terms "high performance"and "engine" are used in the same sentence. Unquestionably,horsepower is heady stuff, capable of not only moving a vehicleto obscene speeds, but also of propelling its owner to a positionof prominence in the eyes of performance enthusiasts
Making A Big Splash In The Marine Market
The average individual that would have owned a performance car in the 1960s, and the baby boomers that did, in many cases no longer have a modern affordable toy they can tweak to their own satisfaction. Serious performance today is often available to only a few with large checking accounts or extra good credit, and
Caliper Clinic: Rebuilders Not Only Can Improve An OE Design, But They Can Also Improve The Consumers’ Opinion
Rebuilders not only can improve an OE design, but they can also improve the consumers’ opinion about the rebuilt auto parts business, in general. Many people still believe that all rebuilt parts are sub-standard compared with original equipment parts. However, most rebuilders are continually working to improve the reputation of rebuilt parts by producing quality
Making Power From Big Block Fords
As noted last month, the first part of a big block Ford power program is to select the appropriate components and machine them properly. Part two entails coordinating the camshaft and valvetrain with an engine’s intended use, and then bolting everything together using proven high performance techniques. According to high performance Ford specialist Norm Wizner,