Rebuilding The Ford 3.0L V6
The 3.0L Ford pushrod motor has been around for nearly 20 years. It was originally introduced back in 1986 and millions of them have been installed in a wide variety of front and rear wheel drive cars and trucks since then. It’s been used in several FWD applications including the Taurus/Sable, the Tempo/Topaz and the
Dodge City’s Finest; Harry’s Machine Works
No history of the American West would be complete without extensive recollections of Dodge City, KS. Formed as a convenient railroad stop to serve the new Atchison, Topeka and Santa Fe railroad, Dodge City offered something for everyone. That is, if your tastes ran to buffalo hunting, gambling or gunfighting. In its early days, Dodge
The Smooth Science of Cylinder Honing
The basics of honing cylinder blocks hasn’t changed much in recent years, but what has changed are the type of abrasives being used by many engine builders. Silicon carbide and aluminum oxide honing stones of various grits have long been used in power honing machines and portable hones to finish cylinder bores. These types
Ford 4.0L V6 Engine
The original 2.6L engine was replaced by the 2.8L, which was upgraded to the 2.9L and then finally bored and stroked to make it into the 4.0L that was used in the Rangers, Aerostars and Explorers starting in 1990. It was replaced by a SOHC engine from this same family at the end of model
Rebuilding the Chevrolet LT1 Engine
Although it shared many common dimensions, looked much the same and even had a few common parts, it was totally redesigned to provide more power with lower emissions and better fuel economy. Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20% more horsepower, got better fuel mileage, and had a
Rebuilding The GM Quad 4
The Quad 4 had four valves per cylinder, tuned intake and exhaust manifolds, no distributor, no plug wires, lightweight rods and pistons to reduce shaking forces, and a crank with eight counterweights that was designed to reduce noise, vibration and harshness (NVH) and bearing wear. It didn’t have an A.I.R. pump or an EGR system,
Why Parts Get Coated
I never would have believed you could get those kind of resultsfrom a glorified paint job. With those words, another skeptic(in this case, a NASCAR Winston Cup engine builder) had come toaccept the value of special coatings applied to engine components. At the time, such skepticism was not totally unwarranted. Likeany emerging technology, the coating
Valvetrains: Better Materials & Design
Pushrods would seem to be an endangered species these days, atleast as far as most new engine designs are concerned. The onlybrand new engines built in recent years with a pushrod valvetrainhave been Chrysler’s 8.0L V10 for the Viper and Dodge Ram, andGeneral Motors new "LS1" 5.7L small block V8. All therest have either been
Rebuilding The Chrysler Engine Family
Much of the information used to write thisarticle was provided by Bruce Chapman, president, and the employeesof Ontario Reman, Etobicoke, Ontario, Canada. Ontario Reman isan authorized Chrysler engine rebuilder selling remanufacturedengines and small parts to Canadian Chrysler dealers. We thankthem! Chrysler introduced a whole new family of 60degree V6 engines beginning with the 3.3L OHV
Making A Big Splash In The Marine Market
The average individual that would have owned a performance car in the 1960s, and the baby boomers that did, in many cases no longer have a modern affordable toy they can tweak to their own satisfaction. Serious performance today is often available to only a few with large checking accounts or extra good credit, and
Performance Small Block: Chevy Engines
Small block Chevy engines long ago became mainstays in both thetraditional and high performance marketplace. So many of themhave been rebuilt over the years, and so much has been writtenabout the rebuilding process, it would appear that nothing moreneed be said. But the small block engine has changed over the years and so haveconsumer preferences
Making Power From Big Block Fords
As noted last month, the first part of a big block Ford power program is to select the appropriate components and machine them properly. Part two entails coordinating the camshaft and valvetrain with an engine’s intended use, and then bolting everything together using proven high performance techniques. According to high performance Ford specialist Norm Wizner,