Turbocharged and Nitrous-Boosted 429 cid LSX Engine - Engine Builder Magazine

Turbocharged and Nitrous-Boosted 429 cid LSX Engine

It's tough to beat the lines and looks of a Chevy Nova. Jason Sack's 1969 Nova is certainly up there in terms of coolest-looking, and it doesn't hurt that it has 2,200+ horsepower under the hood courtesy of a turbocharged and nitrous-boosted 429 cid LSX engine! See for yourself!

Engine of the Week is presented by

By the time we got to Gainesville Raceway for day four of Sick Week, we had already spoken to a number of competitors about their awesome drag-and-drive cars and engine setups. However, there were still a ton more to discover of the more than 300 competitors, and the cars continued to get better and better. Case in point, Jason Sack’s orange and white 1969 Nova named Cowboy Up, which features a 429 cubic inch LSX engine. Jason was checking lash and doing some routine maintenance when we came by his pit area, but he set down the tools a minute to tell us all about the details of his powerful LSX.

Jason Sack at Gainesville Raceway doping some maintenance work on his 1969 Nova.

Of course, the best thing about drag-and-drive events is that you find a mix of competition veterans and newbies. Jason fell into the veteran category, but that doesn’t make the task at hand – finishing the event – any easier. He was at Sick Week competing in the tough Unlimited Iron class against the likes of Steve Morris, Alex Taylor, Tina Pierce, and Bryant Goldstone, among others.

“We got here and tested in Bradenton a couple days before the event started,” Jason Sack says. “However, I was on the struggle bus. The car ran at my house, but when we brought it here it took us six hours with three of us to get it to fire. All we did was switch the fuel. Then, I went all through testing four days and I never made it past 400 feet. Then, the first day in Orlando, I think we went 7.54 at 177 mph or something. Then, the next day, I did a personal mph best of 202 mph. At South Georgia Motorsports Park I did a personal best ET of 7.08. That was a good lick, and it was only on seven cylinders.”

If everything had gone smooth with no issues, Jason expects the Nova could see ETs as low as 6.80s. That’s a far cry from where his Nova initially started.

“The car started out as a small tire 275 with a stock floor and stock frame, a bolt-on front end and then it went to the chassis shop and it just snowballed into a double frame rail,” Sack says. “Skinny Kid Race Cars built the chassis. The engine has a Dart block, All Pro LS7 heads, Jesel shaft rockers, a solid roller camshaft, a BS Racing 106mm turbo, and a Turbosmart wastegate. We also run an intercooler with ice and a six-stage dry sump oiling system from Dailey.

“We just switched to the dry sump for this event. We were having some oil pump cavitation, so we switched to the dry sump and those issues were solved. We start in the morning at 93 psi. I do my burnout at 93 psi and make my hit at 93 psi all the way out the end. It’s just rock solid.

“The engine also has a Callies Magnum crank and R&R aluminum rods, which we just switched to for this event. I leaned on it pretty hard and bent some rods from water getting in the cylinders. I put 50 psi in the radiators and blew them all up, so these are all brand new. I also have custom-made Diamond pistons, a Holley intake and Holley Dominator EFI.”

106mm turbo

Jason’s LSX typically runs on C16 race fuel, but for Sick Week he switched to VP X98, which he says has been awesome. He also added a 10-gpm brushless pump and Injector Clinic 2600 injectors to keep up with the ethanol.

“We also run a Rossler 400 transmission and a Skinny Kid 9” rear with 4.10 gears,” he notes.

In addition to the 106mm turbo, Jason’s Nova gets boost from a 150-hp shot of nitrous that he sprays only on the two step.

“We shut it off at 8-lbs,” he says. “It takes about 7 seconds for this motor to spool that up and when I use the nitrous it cuts it to 2.5 seconds, so it’s just easy. With some tuning, we can probably fix it where we didn’t need it, but once I did it once and it just gets on the chip, I was pretty much sold. I’ll take the weight.”

The BS Racing turbo typically sees no more than 32-lbs. of boost, and Jason told us he was utilizing 31.6-lbs during most of Sick Week.

“We leave on about 18-lbs. at 5,500 rpm and there is no boost ramp,” Sack says. “It’s just whatever that’ll make to get to 31-lbs. as fast as it’ll go, which is usually under half a second.”

With the turbo and nitrous, Jason’s LSX engine makes a safe 2,200 horsepower! However, it can make more power than that, but Jason has seen issues arise at 2,400 horsepower, so he likes to stay under that mark.

The track performance is one thing, but the drives from track to track can be another, and Jason says the Nova does pretty well on the street, but can get quite warm in the car without AC.

“It works absolutely perfect on the drives,” he says. “I changed shocks and put a heavier spring in. However, it gets hot in the car – I mean so hot you get thermal shut down on your phone and your iPad when you’re traveling. You’ve got to hold it out the window to cool it down. It’s probably like 150-160 degrees F in the car while you’re driving. You feel cooked.”

Outside of a personal best 202 mph on one pass and a personal best 7.08 ET on another, Jason’s Sick Week ultimately didn’t go according to plan. Unfortunately, Gainesville was the end of the road for Jason during this year’s Sick Week, so we were glad we got the chance to speak with him. He ultimately turned in ETs of 7.42 at 202 mph, 7.56 at 177 mph and 7.08 at 196 mph. Hopefully, we will see him back next year!

Engine of the Week is sponsored by PennGrade Motor OilElring – Das Original and NPW Companies. If you have an engine you’d like to highlight in this series, please email Engine Builder Editor Greg Jones at [email protected].

You May Also Like

Supercharged 588 cid Hemi Engine

Ken Lazzeri, head engine builder for Indy Cylinder Head, has helped build over 5,000 Hemi engines during the life of the Mopar component manufacturer’s business. We were pumped to get time with him to discuss the details of this 588 cid supercharged Hemi engine for bracket racing. Check it out!

We’ve been following Indy Cylinder Head and the engine work of Ken Lazzeri for a long while now. The company, which specializes in performance components such as intake manifolds, cylinder heads, and engine blocks, does so specifically for the Mopar crowd, and Ken’s engine work follows right behind with some amazing examples of Hemi horsepower.

All-Billet Subaru EJ 2.5L Engine

This 2016 Subaru STi, which features an all-billet EJ 2.5L engine, was built to showcase what Kaiju Motorsports is capable of. Not only does it look great, but all expectation is that it performs well too. Check it out!

Kaiju Motorsports 2016 Subaru STi with a billet EJ 2.5L engine
Turbocharged Billet K24 Honda Engine

Noonan Race Engineering is well-known for its V8 engine platforms, but the shop has now dipped its toe into the 4-cylinder world with a billet K24 Honda engine. The objective – huge horsepower, while keeping factory creature comforts. Check it out!

ProCharged 5.000” Bore Space Billet Big Block Chevy Engine

One of the first 5.000″ bore space big block Chevy engines that Visner Engine Development has come out with in this new design, this billet engine was built by Nick Bacalis of Bullet Racing Engines for a 1971 C10 belonging to Michael Rieck. Check out what 4,000-plus horsepower looks like!

billet big block Chevy engine
3,500+ HP 427 cid Billet LS Engine

At ACE Racing Engines, Stefan Rossi’s and Laura Pugh’s hard work has been paying off in the form of increased awareness and business, a new shop space out in California, and best of all, success on the track from numerous customers. Check out this excellent example of a maximum effort, billet LS engine for a drag-and-drive application.

Other Posts

Inside the Coyote Den of Fast Forward Race Engines

Fast Forward Race Engines and shop owners Joe and Gina Irwin have been making big horsepower and well-performing engines for quite some time. Recently, the shop’s Coyote engine program has been gaining notoriety thanks to the work the shop does in conjunction with Brett LaSala and his record-setting Snot Rocket Mustang. That twin-turbo 5.0L Coyote

Turbocharged 5.9L Cummins Engine

At Back Bay Diesel Performance, repair and performance work are taken very seriously. Those capabilities are often showcased through custom shop builds, like shop owner Adam Nichols’ own turbocharged 5.9L Cummins engine for his personal drag truck. Check it out!

540 cid Small Block John Deere Light Pro Stock Engine

When it comes to PRI booth engines, Fluidampr has been a great booth to visit over the last couple years, and at the 2023 show the company had a VG Motorsports-built small block John Deere Light Pro Stock engine on display that definitely stopped us in our tracks. We got to speak with VG Motorsports

Dave Schroeder’s 872 cid Pro Mod Nitrous Engine

Dave Schroeder and John Ens have been at the drag-and-drive game for a long time. They’ve seen a thing or two and certainly experience3d a thing or two when it comes to this category of racing, and the 872 cid Pro Mod Nitrous engine built by Reher-Morrison is a build that stands out from the