Rebuilding The Ford 2.0L
The old 1.9L was modified and upgraded in the process of making it into the 2.0L. The new engine was bored and stroked, it had siamesed cylinders that made the block stronger and quieter, the crank had four more counterweights that made it run smoother, and it had domed pistons for more compression. The
Flow Boxes
Over the years, I have had occasion to port cylinder heads when I had no prior experience with that particular casting. The results have not always been as good as I would have liked them to be, but with only one head or one pair of heads available to work with, the development opportunities were
The Properties Of Cast Iron
The reality is that much of what you understand and have been taught about welding cast iron may be incorrect. Cast iron is not used because it’s cheap, but because it has very good properties and works extremely well as the metal of choice for many engine blocks and cylinder heads. Cast iron has gotten
Rebuilding the Ford 4.6L SOHC Engine
The 4.6L was lower, shorter and lighter than the 302, but the base engine made more power than the 302, got better fuel economy and passed all the emission tests without a thermactor pump. Ford called it its “modular” engine because it was part of a whole new family of engines that were intended to
Improving engine balance on 1992-2001 GM 6.5L VIN 7, F, P, S and Y diesel truck engines
Engine Builders: The AERA Technical Committee offers the following information on improving engine balance on 1992-2001 GM 6.5L VIN 7, F, P, S and Y diesel truck engines. This information should be considered any time this engine is remanufactured. While some owners of these engines have accepted the original driveability condition as normal, others have
Engine Crack Detection Technology
It doesn’t matter if you’re rebuilding a high mileage engine and reusing salvaged components or using brand new parts right out of the box – any highly stressed component or casting that has to withstand high loads, temperatures and/or pressures should always be inspected to make sure it is free from cracks or other defects
Rebuilding The Ford 3.8L Engine
They needed an economy engine that would fit in their new cars, and they needed it fast. They had a couple of old inline sixes and a small German V6, but none of them were designed for fuel economy or the coming emissions standards, and the 250 cid engine was so tall that it wouldn’t
Rebuilding the Chevrolet LT1 Engine
Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20 percent more horsepower, got better fuel mileage, and had a much broader torque band with 90 percent of its peak torque available from just over 1,000 rpm all the way up to nearly 6,000 rpm. GM Powertrain accomplished all of this by
Rebuilding the Chevrolet LT1 Engine
Although it shared many common dimensions, looked much the same and even had a few common parts, it was totally redesigned to provide more power with lower emissions and better fuel economy. Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20% more horsepower, got better fuel mileage, and had a
Rebuilding The GM Quad 4
The Quad 4 had four valves per cylinder, tuned intake and exhaust manifolds, no distributor, no plug wires, lightweight rods and pistons to reduce shaking forces, and a crank with eight counterweights that was designed to reduce noise, vibration and harshness (NVH) and bearing wear. It didn’t have an A.I.R. pump or an EGR system,
LPG Conversions: Renewed Interest In The Use Of LPG (Liquefied Petroleum Gas) And LNG (Liquefied Natural Gas)
The recent move to clean up inner city exhaustemissions has resulted in renewed interest in the use of LPG (LiquefiedPetroleum Gas) and LNG (Liquefied Natural gas) as motor fuels.These fuels are almost pure propane with a little butane present. Tax incentives are being offered to encouragefleet operators to convert to gaseous fuels and more vehiclesare
Cleaning – Do You Know Where Your Dollars Are?
Cleaning parts in the machine shop doesn’tcome cheaply. According to Automotive Rebuilder’s Machine ShopMarket Profile about 15.2% of engine machining and rebuildingproduction work involves disassembly and cleaning. According torebuilders that we surveyed, disassembly and cleaning accountedfor the highest percentage of total rebuilding production timein the shop. So there can be significant benefits to reducingcleaning costs
Grinding Techniques: In Thousands Of Years, The Basics Of Grinding Haven’t Changed
Grinding is one of the oldest methods known for shaping and sharpening objects. It was first used in prehistoric times to make weapons and other tools by rubbing wood, stones, bones and eventually metal against hard, abrasive rocks. In thousands of years, the basics of grinding haven’t changed. We’re still rubbing an abrasive against metal