In Search Of New Markets, Mike Jeffries
Looking for new markets is one of the toughest things we do, so every time the phone rings we listen for an opportunity. Most of what we find is suspect, but over the past 12 months we have rebuilt a number of compact diesels and sold a number of rebuild kits. As a result we
I can’t seem to trace a coolant leak in a 4.3L GM. Can you help?
A. Coolant loss on 1992-1997 4.3L GM VIN R & W engines has been, at times, difficult to detect. The cause of the coolant loss has been traced to cracks that may develop in the lifter valley area of the block and allow coolant to pass into the valley of the block. This loss of
Cylinder liner adjustment and compression ring gasket thickness for Detroit Diesel Corporation (DDC) 71 Series diesel engines
Engine Builders: The following information regards cylinder liner adjustment and compression ring gasket thickness for Detroit Diesel Corporation (DDC) 71 Series diesel engines. This information should be considered any time liners are replaced. AERA previously published TB 206 concerning compression ring gaskets. This supplements that information. The correct position of the liner top flange is
The New Sport Compact Market
The most popular nameplates are imports such as Honda, Acura and Mitsubishi, but coming on fast are Nissan, Toyota, Mazda, Subaru and Volkswagen – plus domestic models such as Ford Focus, Dodge Neon and even Chevy Cavalier. Nobody is abandoning the small block Chevy or any of the other V8s that have traditionally been the
What’s Wrong With Our Industry
What’s wrong with the engine building industry today? It’s a simple question that has no simple answer. Like many other – if not every – industry facing difficult times, the factors impacting this market are varied, complex and frustratingly hard to pin down. Are the woes of the industry the fault of customers or suppliers?
What is the cylinder head installation procedure for the new GM 6.6L diesel engine?
What is the cylinder head installation procedure for the new GM 6.6L diesel engine? According to the AERA technical committee, there is a revised cylinder head installation procedure for 2001-2003 GM 6.6L VIN 1 diesel engines. These engines are referred to as Duramax diesels and are a result of a joint venture between GM and
Increased crankshaft journal dimensions for 1995-2002 Kia 1.8L VIN 5 engines.
Engine Builders: The AERA Technical Committee offers the following information on increased crankshaft journal dimensions for 1995-2002 Kia 1.8L VIN 5 engines. The main journal diameter for the crankshaft of this engine was increased beginning with the 1998 model year. Mazda manufactured these engines prior to 1998 while Kia manufactured all subsequent engines. Use caution
The lower intake manifolds on some Ford vehicle models are not fitting correctly after machining
Engine Builders: Some AERA members have reported that the lower intake manifolds on some Ford vehicle models are not fitting correctly after machining. To reduce the likelihood of coolant contamination of engine oil, a revised, thicker intake gasket is now available for the 3.8L and 4.2L Ford car and truck engines. These models have VIN
Eliminate head gasket failures on Cat diesels
Q. To eliminate head gasket failures on Cat diesels, how should the heads be torqued? A. Pressurizing the cooling system with the oil pan removed can differentiate between a water pump leak and a cylinder head gasket leak before removing the head. If a head gasket is the source of the problem this revised cylinder
Compromising the Seal
The head gasket is one of the most critical gaskets in an engine because it has to seal all of the combustion chambers as well as the coolant and oil passages between the head and block. The gasket has to provide a leak-free seal from the moment it is first installed, and maintain that seal
Improving engine balance on 1992-2001 GM 6.5L VIN 7, F, P, S and Y diesel truck engines
Engine Builders: The AERA Technical Committee offers the following information on improving engine balance on 1992-2001 GM 6.5L VIN 7, F, P, S and Y diesel truck engines. This information should be considered any time this engine is remanufactured. While some owners of these engines have accepted the original driveability condition as normal, others have
Rebuilding The Ford 3.8L Engine
They needed an economy engine that would fit in their new cars, and they needed it fast. They had a couple of old inline sixes and a small German V6, but none of them were designed for fuel economy or the coming emissions standards, and the 250 cid engine was so tall that it wouldn’t
Coretalk: September 2001
Ford Plans to Revamp Parts Distribution Network Ford Motor Co. is working to restructure and expand its United States parts distribution network to deliver service and repair parts to its dealers faster and more efficiently. Over the next three years, Ford plans to increase the number of parts distribution centers from 10 to 21, creating
Back to Basics: Preventing Piston Problems
Burned pistons. Scuffed pistons. Cracked pistons. These are problems no customer wants to experience in an engine you’ve built. Warranty claims can kill your business, so here are some tips on how to prevent these and other common piston problems. First and foremost, if you’re custom building an engine that has already suffered some kind
Back to Basics: Gasket Installation Tips and Tricks
The installation of gaskets is one of the most important aspects of rebuilding an engine. Gaskets provide a seal between mating surfaces so oil, coolant, vacuum and pressure don
Torque-to-Angle/Yield Threaded Fasteners
All the original equipment manufacturers (OEMs) have fastener labs with lots of sophisticated equipment and well-educated people working on fastening issues. They even have their own professional association – The Bolting Technology Council – which holds meetings and seminars about fasteners. I’m not a fastener engineer, and I’m not going to make you into one.
Threaded Fasteners Torque-to-Yield and Torque-to-Angle
All the original equipment manufacturers (OEMs) have fastener labs with lots of sophisticated equipment and well-educated people working on fastening issues. They even have their own professional association – The Bolting Technology Council – which holds meetings and seminars about fasteners. I’m not a fastener engineer, and I’m not going to make you into one.
Rebuilding the GM / Chevy 2.2L Engine
Unfortunately, this four cylinder, pushrod motor didn’t have nearly enough horsepower, so Buick, Oldsmobile and Pontiac all opted for the 1.8L SOHC Opel engine from Brazil for most of their “J” cars, and Chevy promptly made its new engine into a 2.0L/121 cid that delivered more power in 1983. The 2.0L was upgraded in 1987
Rebuilding the Chevrolet LT1 Engine
Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20 percent more horsepower, got better fuel mileage, and had a much broader torque band with 90 percent of its peak torque available from just over 1,000 rpm all the way up to nearly 6,000 rpm. GM Powertrain accomplished all of this by
Rebuilding the Chevrolet LT1 Engine
Although it shared many common dimensions, looked much the same and even had a few common parts, it was totally redesigned to provide more power with lower emissions and better fuel economy. Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20% more horsepower, got better fuel mileage, and had a