Back to Basics: Preventing Piston Problems
Burned pistons. Scuffed pistons. Cracked pistons. These are problems no customer wants to experience in an engine you’ve built. Warranty claims can kill your business, so here are some tips on how to prevent these and other common piston problems. First and foremost, if you’re custom building an engine that has already suffered some kind
Torque-to-Angle/Yield Threaded Fasteners
All the original equipment manufacturers (OEMs) have fastener labs with lots of sophisticated equipment and well-educated people working on fastening issues. They even have their own professional association – The Bolting Technology Council – which holds meetings and seminars about fasteners. I’m not a fastener engineer, and I’m not going to make you into one.
Threaded Fasteners Torque-to-Yield and Torque-to-Angle
All the original equipment manufacturers (OEMs) have fastener labs with lots of sophisticated equipment and well-educated people working on fastening issues. They even have their own professional association – The Bolting Technology Council – which holds meetings and seminars about fasteners. I’m not a fastener engineer, and I’m not going to make you into one.
Engine Cylinder Bore Surface Finishes
What’s the best type of cylinder bore finish for today’s engines? Most would say it’s a finish that allows the rings to seat quickly and completely so the engine doesn’t use oil. For many applications, that may mean a plateau finish. The surface finish must also meet the piston ring manufacturer’s specifications and have the
Rebuilding the GM / Chevy 2.2L Engine
Unfortunately, this four cylinder, pushrod motor didn’t have nearly enough horsepower, so Buick, Oldsmobile and Pontiac all opted for the 1.8L SOHC Opel engine from Brazil for most of their “J” cars, and Chevy promptly made its new engine into a 2.0L/121 cid that delivered more power in 1983. The 2.0L was upgraded in 1987
Rebuilding the New Chevy 262
This enabled GM to shorten the development process dramatically because it was able to adapt a proven design. But it also allowed it to share a lot of the existing tooling from the V8 production lines so the engines could be on the road sooner. The original 200 V6 that came out in 1978 was
Rebuilding the Chevrolet LT1 Engine
Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20 percent more horsepower, got better fuel mileage, and had a much broader torque band with 90 percent of its peak torque available from just over 1,000 rpm all the way up to nearly 6,000 rpm. GM Powertrain accomplished all of this by
Rebuilding the Chevrolet LT1 Engine
Although it shared many common dimensions, looked much the same and even had a few common parts, it was totally redesigned to provide more power with lower emissions and better fuel economy. Compared to the 1991 Chevy 350 L98 with TPI, the LT1 made 20% more horsepower, got better fuel mileage, and had a
Rebuilding Toyota 3.0L V6 Engine
In 1988 Toyota introduced its first V6. Most of the information that follows applies to the 3.0L version used in Toyota’s truck applications. The 3.4L is still fairly new to the aftermarket at this point. 3VZ-E – 3.0L SOHC V6 – ’88-’95 The 3VZ-E was also introduced for the 1988 model year on Toyota 4×4
Rebuilding The GM Quad 4
The Quad 4 had four valves per cylinder, tuned intake and exhaust manifolds, no distributor, no plug wires, lightweight rods and pistons to reduce shaking forces, and a crank with eight counterweights that was designed to reduce noise, vibration and harshness (NVH) and bearing wear. It didn’t have an A.I.R. pump or an EGR system,
The Fit Is In The Finish
Clean, flat and smooth. These three words describe the surface in an engine, not just the head and block. But how clean, how flat and how smooth do the surfaces really have to be to get a good, long lasting seal? It depends on the application. Clean means no dirt, oil, grease or residual gasket
Rebuilding the Buick 3300
The Buick 3300 was introduced in 1989 as areplacement for the 3.0L that had been around since 1982. It hadthe updated block with on-center bores, just like the revisedversion of the 3800 that came out the year before, along withseveral other changes and improvements. This engine was installed in many of the "A"bodied cars including
“Heading” In The Right Direction: Heads Are A Hot Commodity These Days
Heads are a hot commodity these days, but itdepends on the application. Some heads like those for Chevy 350and Chrysler 2.2L/2.5L engines are always in demand, but pricesare low because of the glut of cores that are available for theseengines. Even so, anybody who’s selling heads these days has tohave them. The hot heads are
Updating The Asian Import Engine Market: The Learning Curve For Part Identification
"The learning curve for part identificationis awesome" says Bob Gibson as he describes the difficultiesof imported engine core identification. As vice president forsales and marketing at Engine Masters, Inc., a Dallas, TX, productionengine rebuilder, Gibson knows that the demand for import enginerebuilding is growing, and that he’ll do what it takes to be apart of
Small Engine Performance
Most businesses have the same problems and each must look for ways to remain competitive by reducing costs and exploring new markets for existing products or services. And so it is in engine building. There is always someone that is able to provide more features per dollar than you (or at least make someone believe
Mopar Engine Platforms – 318, 360
Chrysler Corp. hasn’t built a rear wheel drive, V8-powered car (with the exception of the Viper) since the turn of the decade. And the cars that harbored V8s beneath their hoods during the late 1980s were about as appealing to performance enthusiasts as the front-wheel driven vehicles that replaced them. In spite of that fact,
Valvetrains: Better Materials & Design
Pushrods would seem to be an endangered species these days, atleast as far as most new engine designs are concerned. The onlybrand new engines built in recent years with a pushrod valvetrainhave been Chrysler’s 8.0L V10 for the Viper and Dodge Ram, andGeneral Motors new "LS1" 5.7L small block V8. All therest have either been
Niche Market Opportunities
In today’s highly competitive market, it makes sense to constantlybe on the lookout for new opportunities. Information on the marketsdescribed in this article may provide some new business prospectsfor those shops not already involved with them. However, rebuildersshould constantly be prospecting for other niche markets for theirexisting products or services. There are potentially many products
Rebuilding The Chrysler Engine Family
Much of the information used to write thisarticle was provided by Bruce Chapman, president, and the employeesof Ontario Reman, Etobicoke, Ontario, Canada. Ontario Reman isan authorized Chrysler engine rebuilder selling remanufacturedengines and small parts to Canadian Chrysler dealers. We thankthem! Chrysler introduced a whole new family of 60degree V6 engines beginning with the 3.3L OHV
Machine Shop Market Profile
As is generally already known, the machineshop/custom engine rebuilder market struggled in 1996 to keeppace with production numbers generated in 1995. Many shop ownerstold us that demand was flat for machine shop services and/orrebuilt engines during 1996. Verification of these shop owners’ commentswas generated in our annual survey of the membership of the AutomotiveEngine Rebuilders